FTCS-B3325G-40D 25G SFP28 BIDI光模块 40km(1330T/1270R)

产品概述 / Description

FTCS-B3325G-40D 是北亿纤通(F-tone Networks)25.78Gbps SFP28 单纤双向光模块,发射波长 1330nm、接收波长 1270nm,采用 DFB 激光器与 APD 雪崩光电探测器,单模光纤最远传输 40km,单 LC 接口,一根光纤完成双向传输,节省一半光纤资源,适用于 5G 前传长距离拉远与城域接入。

产品特点 / Product Features

  • Up to 25.78Gbps Data Links
  • Up to 40km transmission on SMF
  • 1330nm/1270nm DFB Laser and APD receiver
  • Metal enclosure, for lower EMI
  • 2-wire interface with integrated Digital Diagnostic monitoring
  • Hot-pluggable SFP28 footprint
  • Compliant with SFP+ MSA and SFF-8472 with duplex LC receptacle
  • Single 3.3V power supply
  • Power dissipation < 1.5 W
  • Operating case temperature:0 to +70°C

应用场景 / Applications

  • 25GBASE-ER
  • eCPRI and CPRI

Standard

  • Compliant with SFF-8472 &8431
  • RoHS Compliant.

25G SFP28 BIDI 光模块产品外观(单 LC 接口)

功能框图 / Transceiver Functional Diagram

模块由发射、接收与控制三部分组成:发射侧由 MCU 通过 LD Bias / MOD-DEF 控制激光器驱动器(LD Driver),驱动 DFB 激光器输出光信号;接收侧由 PIN 光电探测器(内置跨阻放大器 TIA)与后级限幅放大器(Post Amp)恢复电信号;MCU 经 I2C(SDA/SCL)对外提供温度、电压、偏置电流、收发光功率等数字诊断信息,并处理 TX Disable、TX Fault、LOS 等控制与告警信号。

技术参数 / Specifications

绝对最大额定值 / Absolute Maximum Ratings

Parameter Symbol Min Max Unit
Storage Temperature Ts -40 85 ºC
Relative Humidity RH 5 95 %
Power Supply Voltage VCC -0.3 4 V
Signal Input Voltage VSI Vcc-0.3 Vcc+0.3 V
Rx Damage Threshold PRdmg -3 dBm

推荐工作条件 / Recommended Operating Conditions

Parameter Symbol Min Typical Max Unit
Case Operating Temperature Tcase 0 70 ºC
Power Supply Voltage VCC 3.14 3.3 3.47 V
Power Supply Current ICC 420 mA
Data Rate BR 25.78 Gbps
Transmission Distance TD 40 km
Coupled fiber Single mode fiber

光学与电特性 / Optical and Electrical Characteristics

Parameter Symbol Min Typical Max Unit Notes
Transmitter
Centre Wavelength λc 1320 1330 1340 nm
Spectral Width(-20dB) Δλ 1 nm
Average Output Power Pout 0 6 dBm
Average Launched Power(Laser Off) Poff -30 dBm
Extinction Ratio ER 3.5 dB 1
Input differential impedance Rin 100 Ω 2
Single ended data input swing Vin,pp 180 700 mV
TX Disable Disable 2.0 Vcc+0.3 V
Enable 0 0.8 V
TX Fault Fault 2.0 Vcc+0.3 V
Normal 0 0.8 V
Output Eye Mask {0.31,0.4,0.45,0.34,0.38,0.4}
Receiver
Centre Wavelength λc 1260 1270 1280 nm
Receiver Sensitivity -17.5 dBm 3
Input Saturation Power (Overload) -6 dBm
Los Of Signal Assert PA -35 dBm
Los Of Signal De-assert PD -19 dBm
LOS -Hysteresis PHys 0.5 2 6 dB
Differential data output swing Vout,pp 300 850 mV 4
LOS High 2.0 Vcc+0.3 V
Low 0.8 V

Notes:

Measured with a PRBS 231-1 test pattern, @25.78Gb/s.

Connected directly to TX data input pins. AC coupled thereafter.

ER=3.5dB; BER =<5X10-5 @PRBS=231-1 NRZ.

Into 100 ohms differential termination.

引脚定义 / Pin Descriptions

引脚定义 / Pin Descriptions

Pin Symbol Name/Description Notes
1 VEET Transmitter Ground (Common with Receiver Ground) 1
2 TFAULT Transmitter Fault. 2
3 TDIS Transmitter Disable. Laser output disabled on high or open. 3
4 SDA 2-wire Serial Interface Data Line 4
5 SCL 2-wire Serial Interface Clock Line 4
6 MOD_ABS Module Absent. Grounded within the module 4
7 RS0 Rate Select 0, internal pull down 5
8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 6
9 RS1 Rate Select 1, internal pull down 5
10 VEER Receiver Ground (Common with Transmitter Ground) 1
11 VEER Receiver Ground (Common with Transmitter Ground) 1
12 RD- Receiver Inverted DATA out. AC Coupled
13 RD+ Receiver Non-inverted DATA out. AC Coupled
14 VEER Receiver Ground (Common with Transmitter Ground) 1
15 VCCR Receiver Power Supply
16 VCCT Transmitter Power Supply
17 VEET Transmitter Ground (Common with Receiver Ground) 1
18 TD+ Transmitter Non-Inverted DATA in. AC Coupled.
19 TD- Transmitter Inverted DATA in. AC Coupled.
20 VEET Transmitter Ground (Common with Receiver Ground) 1

Notes:

Circuit ground is internally isolated from chassis ground.

TFAULT is an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V.A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V.

Laser output disabled on TDIS>2.0V or open, enabled on TDIS<0.8V.

Should be pulled up with 4.7kΩ- 10kΩ host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in.

Rate select can also be set through the 2-wire bus in accordance with SFF-8472. Rx Rate Select is set at Bit 3, Byte 110, Address A2h. Tx Rate Select is set at Bit 3, Byte 118, Address A2h.

LOS is open collector output. It should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

推荐接口电路 / Recommended Interface Circuit

推荐接口电路 / Recommended Interface Circuit

机械尺寸 / Mechanical Dimensions

机械尺寸 / Mechanical Dimensions

订购信息 / Ordering Information

Part Number Product Description
FTCS-B3325G-40D 1330T/1270R, 25.78Gbps, LC, 40km, 0°C~+70°C, with DDM

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.

公司名:北亿纤通 | F-tone Networks
地区:中国四川天府新区
服务区域:全球
联系方式:
企业电话:028-85255257 | 企业传真:028-85977702 | 企业手机:19081343401
Site:https://www.f-tone.com
人事部:hr@f-tone.com | 市场部:sales@f-tone.com | 技术支持:support@f-tone.com

本产品为光模块产品线,详细信息,请联系我们的销售人员,谢谢!

Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.