产品概述 / Description
FTCS-B3325G-20DI 是北亿纤通(F-tone Networks)推出的 25.78Gbps SFP28 单模单纤双向(BIDI)光收发模块,发射端 1330nm DFB 激光器,接收端 1270nm PIN 光电二极管(内置跨阻放大器 TIA),在单模光纤上最远传输 20km,工作温度 -40~+85℃(工业级)。
The SFP28 transceivers are high performance, cost effective modules supporting data rate of 25.78Gbps and 20km transmission distance with SMF. The transceiver consists of three sections: a DFB laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements. The transceivers are compatible with SFP Multi-Source Agreement and SFF-8472 digital diagnostics functions.

产品特点 / Product Features
- Supports up to 25.78Gbps bit rates
- Up to 20km transmission on SMF
- 1330nm TX / 1270nm RX,DFB 激光器 + PIN 探测器
- Hot-pluggable SFP+ footprint
- Compliant with SFP+ MSA and SFF-8472 with single LC receptacle
- Compatible with RoHS
- Single +3.3V power supply
- Real Time Digital Diagnostic Monitoring
- Operating case temperature: -40 to +85°C(工业级)
应用场景 / Applications
- 25GBASE-LR
- eCPRI and CPRI
- 5G 前传单纤双向承载
- 数据中心与城域 25G 单纤互连
功能框图 / Transceiver functional diagram
模块由 LD Driver、DFB 激光器(LD)、PIN+TIA 接收组件、后置放大器(Post Amp)、I2C 控制器与 EEPROM、ADC/DAC 组成,内部监控 Temp、Vcc、LD Bias、Tx Power、Rx Power 等参数,并通过 TD+/-、RD+/-、TxFault、TxDis、LOS、SCL/SDA 与主机交互。
技术参数 / Specifications
绝对最大额定值 / Absolute Maximum Ratings
| Parameter | Symbol | Min | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | Vcc | -0.5 | 4.5 | V |
| Storage Temperature | Ts | -40 | +85 | °C |
| Operating Humidity | – | 5 | 85 | % |
推荐工作条件 / Recommended Operating Conditions
| Parameter | Symbol | Min | Typical | Max | Unit |
|---|---|---|---|---|---|
| Operating Case Temperature | Tc | -40 | +85 | °C | |
| Power Supply Voltage | Vcc | 3.135 | 3.30 | 3.465 | V |
| Power Supply Current | Icc | 400 | mA | ||
| Data Rate | 25.78 | Gbps |
光学与电特性 / Optical and Electrical Characteristics
| Parameter | Symbol | Min | Typical | Max | Unit | Notes |
|---|---|---|---|---|---|---|
| Transmitter | ||||||
| Centre Wavelength | λc | 1320 | 1330 | 1340 | nm | |
| Spectral Width(-20dB) | Δλ | 1 | nm | |||
| Side-Mode Suppression Ratio | SMSR | 30 | – | dB | ||
| Average Output Power | Pout | 0 | 6 | dBm | 1 | |
| Extinction Ratio | ER | 3.5 | dB | |||
| Data Input Swing Differential | VIN | 180 | 850 | mV | 2 | |
| Input Differential Impedance | ZIN | 90 | 100 | 110 | Ω | |
| TX Disable | Disable | 2.0 | Vcc | V | ||
| TX Disable | Enable | 0 | 0.8 | V | ||
| TX Fault | Fault | 2.0 | Vcc | V | ||
| TX Fault | Normal | 0 | 0.8 | V | ||
| Receiver | ||||||
| Centre Wavelength | λc | 1260 | 1270 | 1280 | nm | |
| Receiver Sensitivity | -13.3 | dBm | 3 | |||
| Receiver Overload | 2 | dBm | 3 | |||
| LOS De-Assert | LOSD | -15 | dBm | |||
| LOS Assert | LOSA | -30 | dBm | |||
| LOS Hysteresis | 0.5 | dB | ||||
| Data Output Swing Differential | Vout | 300 | 900 | mV | 4 | |
| LOS | High | 2.0 | Vcc | V | ||
| LOS | Low | 0 | 0.8 | V | ||
Notes:
1. The optical power is launched into SMF.
2. PECL input, internally AC-coupled and terminated.
3. Measured with a PRBS 2³¹-1 test pattern @25.78Gbps, BER ≤5×10⁻⁵.
4. Internally AC-coupled.
时序与电特性 / Timing and Electrical
| Parameter | Symbol | Min | Typical | Max | Unit |
|---|---|---|---|---|---|
| Tx Disable Negate Time | t_on | 2 | ms | ||
| Tx Disable Assert Time | t_off | 100 | µs | ||
| Time To Initialize, including Reset of Tx Fault | t_init | 300 | ms | ||
| Tx Fault Assert Time | t_fault | 100 | µs | ||
| Tx Disable To Reset | t_reset | 10 | µs | ||
| LOS Assert Time | t_loss_on | 100 | µs | ||
| LOS De-assert Time | t_loss_off | 100 | µs | ||
| Serial ID Clock Rate | f_serial_clock | 100 | 400 | KHz | |
| MOD_DEF (0:2)-High | VH | 2 | Vcc | V | |
| MOD_DEF (0:2)-Low | VL | 0.8 | V |
数字诊断 / Diagnostics
| Parameter | Range | Unit | Accuracy | Calibration |
|---|---|---|---|---|
| Temperature | -40 to +85 | °C | ±3°C | Internal |
| Voltage | 3.0 to 3.6 | V | ±3% | Internal |
| Bias Current | 0 to 100 | mA | ±10% | Internal |
| TX Power | 0 to 6 | dBm | ±3dB | Internal |
| RX Power | -14 to +2 | dBm | ±3dB | Internal |
数字诊断存储映射 / Digital Diagnostic Memory Map
The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA). The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring. The digital diagnostic memory map specific data field defines as following.

引脚定义 / Pin Descriptions

| Pin | Signal Name | Description | Plug Seq. | Notes |
|---|---|---|---|---|
| 1 | VEET | Transmitter Ground | 1 | |
| 2 | TX FAULT | Transmitter Fault Indication | 3 | Note 1 |
| 3 | TX DISABLE | Transmitter Disable | 3 | Note 2 |
| 4 | SDA | SDA Serial Data Signal | 3 | |
| 5 | SCL | SCL Serial Clock Signal | 3 | |
| 6 | MOD_ABS | Module Absent. Grounded within the module | 3 | |
| 7 | RS0 | Not Connected | 3 | |
| 8 | LOS | Loss of Signal | 3 | Note 3 |
| 9 | RS1 | Not Connected | 3 | |
| 10 | VEER | Receiver ground | 1 | |
| 11 | VEER | Receiver ground | 1 | |
| 12 | RD- | Inv. Received Data Out | 3 | Note 4 |
| 13 | RD+ | Received Data Out | 3 | Note 4 |
| 14 | VEER | Receiver ground | 1 | |
| 15 | VCCR | Receiver Power Supply | 2 | |
| 16 | VCCT | Transmitter Power Supply | 2 | |
| 17 | VEET | Transmitter Ground | 1 | |
| 18 | TD+ | Transmit Data In | 3 | Note 5 |
| 19 | TD- | Inv. Transmit Data In | 3 | Note 5 |
| 20 | VEET | Transmitter Ground | 1 |
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2) Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3) LOS is open collector output. Should be pulled up with 4.7k~10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
4) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES.
5) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.
推荐接口电路 / Recommended Interface Circuit

机械尺寸 / Mechanical Dimensions

订购信息 / Ordering Information
| Part Number | Product Description |
|---|---|
| FTCS-B3325G-20DI | 1330T/1270R, 25.78Gbps, LC, 20km, -40°C~+85°C, with DDM |
地区:中国四川天府新区
服务区域:全球
联系方式:
企业电话:028-85255257 | 企业传真:028-85977702 | 企业手机:19081343401
Site:https://www.f-tone.com
人事部:hr@f-tone.com | 市场部:sales@f-tone.com | 技术支持:support@f-tone.com
本产品为光模块产品线,详细信息,请联系我们的销售人员,谢谢!
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.



















