FTCS-B3325G-20D 25G SFP28 BIDI光模块 20km(1330T/1270R)

产品概述 / Description

FTCS-B3325G-20D 是北亿纤通(F-tone Networks)推出的 25.78Gbps SFP28 单模单纤双向(BIDI)光收发模块,发射端 1330nm DFB 激光器,接收端 1270nm PIN 光电二极管(内置跨阻放大器 TIA),在单模光纤上最远传输 20km,工作温度 0~+70℃(商业级)。

The SFP28 transceivers are high performance, cost effective modules supporting data rate of 25.78Gbps and 20km transmission distance with SMF. The transceiver consists of three sections: a DFB laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements. The transceivers are compatible with SFP Multi-Source Agreement and SFF-8472 digital diagnostics functions.

FTCS-B3325G-20D 25G SFP28 BIDI 光模块产品外观图

产品特点 / Product Features

  • Supports up to 25.78Gbps bit rates
  • Up to 20km transmission on SMF
  • 1330nm TX / 1270nm RX,DFB 激光器 + PIN 探测器
  • Hot-pluggable SFP+ footprint
  • Compliant with SFP+ MSA and SFF-8472 with single LC receptacle
  • Compatible with RoHS
  • Single +3.3V power supply
  • Real Time Digital Diagnostic Monitoring
  • Operating case temperature: 0 to +70°C(商业级)

应用场景 / Applications

  • 25GBASE-LR
  • eCPRI and CPRI
  • 5G 前传单纤双向承载
  • 数据中心与城域 25G 单纤互连

功能框图 / Transceiver functional diagram

模块由 LD Driver、DFB 激光器(LD)、PIN+TIA 接收组件、后置放大器(Post Amp)、I2C 控制器与 EEPROM、ADC/DAC 组成,内部监控 Temp、Vcc、LD Bias、Tx Power、Rx Power 等参数,并通过 TD+/-、RD+/-、TxFault、TxDis、LOS、SCL/SDA 与主机交互。

技术参数 / Specifications

绝对最大额定值 / Absolute Maximum Ratings

Parameter Symbol Min Max Unit
Supply Voltage Vcc -0.5 4.5 V
Storage Temperature Ts -40 +85 °C
Operating Humidity – 5 85 %

推荐工作条件 / Recommended Operating Conditions

Parameter Symbol Min Typical Max Unit
Operating Case Temperature Tc 0 +70 °C
Power Supply Voltage Vcc 3.135 3.30 3.465 V
Power Supply Current Icc 400 mA
Data Rate 25.78 Gbps

光学与电特性 / Optical and Electrical Characteristics

Parameter Symbol Min Typical Max Unit Notes
Transmitter
Centre Wavelength λc 1320 1330 1340 nm
Spectral Width(-20dB) Δλ 1 nm
Side-Mode Suppression Ratio SMSR 30 – dB
Average Output Power Pout 0 6 dBm 1
Extinction Ratio ER 3.5 dB
Data Input Swing Differential VIN 180 850 mV 2
Input Differential Impedance ZIN 90 100 110 Ω
TX Disable Disable 2.0 Vcc V
TX Disable Enable 0 0.8 V
TX Fault Fault 2.0 Vcc V
TX Fault Normal 0 0.8 V
Receiver
Centre Wavelength λc 1260 1270 1280 nm
Receiver Sensitivity -13.3 dBm 3
Receiver Overload 2 dBm 3
LOS De-Assert LOSD -15 dBm
LOS Assert LOSA -30 dBm
LOS Hysteresis 0.5 dB
Data Output Swing Differential Vout 300 900 mV 4
LOS High 2.0 Vcc V
LOS Low 0 0.8 V

Notes:
1. The optical power is launched into SMF.
2. PECL input, internally AC-coupled and terminated.
3. Measured with a PRBS 2³¹-1 test pattern @25.78Gbps, BER ≤5×10⁻⁵.
4. Internally AC-coupled.

时序与电特性 / Timing and Electrical

Parameter Symbol Min Typical Max Unit
Tx Disable Negate Time t_on 2 ms
Tx Disable Assert Time t_off 100 µs
Time To Initialize, including Reset of Tx Fault t_init 300 ms
Tx Fault Assert Time t_fault 100 µs
Tx Disable To Reset t_reset 10 µs
LOS Assert Time t_loss_on 100 µs
LOS De-assert Time t_loss_off 100 µs
Serial ID Clock Rate f_serial_clock 100 400 KHz
MOD_DEF (0:2)-High VH 2 Vcc V
MOD_DEF (0:2)-Low VL 0.8 V

数字诊断 / Diagnostics

Parameter Range Unit Accuracy Calibration
Temperature 0 to +70 °C ±3°C Internal
Voltage 3.0 to 3.6 V ±3% Internal
Bias Current 0 to 100 mA ±10% Internal
TX Power 0 to 6 dBm ±3dB Internal
RX Power -14 to +2 dBm ±3dB Internal

数字诊断存储映射 / Digital Diagnostic Memory Map

The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA). The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring. The digital diagnostic memory map specific data field defines as following.

FTCS-B3325G-20D 数字诊断存储映射(Digital Diagnostic Memory Map)

引脚定义 / Pin Descriptions

FTCS-B3325G-20D SFP28 引脚定义图(Pin out)

Pin Signal Name Description Plug Seq. Notes
1 VEET Transmitter Ground 1
2 TX FAULT Transmitter Fault Indication 3 Note 1
3 TX DISABLE Transmitter Disable 3 Note 2
4 SDA SDA Serial Data Signal 3
5 SCL SCL Serial Clock Signal 3
6 MOD_ABS Module Absent. Grounded within the module 3
7 RS0 Not Connected 3
8 LOS Loss of Signal 3 Note 3
9 RS1 Not Connected 3
10 VEER Receiver ground 1
11 VEER Receiver ground 1
12 RD- Inv. Received Data Out 3 Note 4
13 RD+ Received Data Out 3 Note 4
14 VEER Receiver ground 1
15 VCCR Receiver Power Supply 2
16 VCCT Transmitter Power Supply 2
17 VEET Transmitter Ground 1
18 TD+ Transmit Data In 3 Note 5
19 TD- Inv. Transmit Data In 3 Note 5
20 VEET Transmitter Ground 1

Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2) Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3) LOS is open collector output. Should be pulled up with 4.7k~10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
4) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES.
5) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.

推荐接口电路 / Recommended Interface Circuit

FTCS-B3325G-20D 推荐接口电路(Recommended Interface Circuit)

机械尺寸 / Mechanical Dimensions

FTCS-B3325G-20D SFP28 机械尺寸图(单位:mm)

订购信息 / Ordering Information

Part Number Product Description
FTCS-B3325G-20D 1330T/1270R, 25.78Gbps, LC, 20km, 0°C~+70°C, with DDM
公司名:北亿纤通 | F-tone Networks
地区:中国四川天府新区
服务区域:全球
联系方式:
企业电话:028-85255257 | 企业传真:028-85977702 | 企业手机:19081343401
Site:https://www.f-tone.com
人事部:hr@f-tone.com | 市场部:sales@f-tone.com | 技术支持:support@f-tone.com

本产品为光模块产品线,详细信息,请联系我们的销售人员,谢谢!

Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.