FTCS-Cxx25G-10D-xx 25G SFP28 CWDM光模块 10km(Level1/2/3 三档)

产品特点 / Product Features

  • Supports up to 25.78Gbps bit rates
  • Hot-pluggable SFP+ footprint
  • CWDM DFB laser and PIN photodiode, Up to 10km for SMF transmission
  • Compliant with SFP+ MSA and SFF-8472 with duplex LC receptacle
  • Compatible with RoHS
  • Single +3.3V power supply
  • Real Time Digital Diagnostic Monitoring
  • Operating case temperature:
  • Standard: 0 to +70°C

25G SFP28 CWDM 光模块产品外观(双工 LC 接口)

应用场景 / Applications

  • 25GBASE-LR

产品概述 / Description

FTCS-Cxx25G-10D-xx 是北亿纤通(F-tone Networks)25.78Gbps SFP28 CWDM 光模块,波长覆盖 1271~1371nm 共 6 个通道(20nm 间隔),单模光纤传输 10km。与标准型号不同的是,该系列按发射光功率与接收灵敏度分为 Level1、Level2、Level3 三个档位,订购时以型号后缀区分,可分别覆盖短距低成本链路、标准 10km 链路与高灵敏度长跨距链路。

The SFP28 transceivers are high performance, cost effective modules supporting data rate of 25.78Gbps and 10km transmission distance with SMF.

The transceiver consists of three sections: a DFB laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.

The transceivers are compatible with SFP Multi-Source Agreement and SFF-8472 digital diagnostics functions.

技术参数 / Specifications

内部 CDR 锁定模式 / Internal CDR Locking Modes

Bits 110.3 and bits 118.3 control the locking modes of the internal retimer or CDR, default Value is “1”.

Bit 110.3 of A2h Bit 118.3 of A2h RX Data Rate TX Data Rate Status of RX CDR Status of TX CDR
High/1 High/1 24.33G/25.78G 24.33G/25.78G CDR select CDR select
High/1 Low/0 24.33G/25.78G 9.95G/10.31G CDR select CDR bypass
Low/0 High/1 9.95G/10.31G 24.33G/25.78G CDR bypass CDR select
Low/0 Low/0 9.95G/10.31G 9.95G/10.31G CDR bypass CDR bypass

功能框图 / Transceiver Functional Diagram

模块由发射、接收与控制三部分组成:发射侧由 MCU 通过 LD Bias / MOD-DEF 控制激光器驱动器(LD Driver),驱动 DFB 激光器输出光信号;接收侧由 PIN 光电探测器(内置跨阻放大器 TIA)与后级限幅放大器(Post Amp)恢复电信号;MCU 经 I2C(SDA/SCL)对外提供温度、电压、偏置电流、收发光功率等数字诊断信息,并处理 TX Disable、TX Fault、LOS 等控制与告警信号。

绝对最大额定值 / Absolute Maximum Ratings

Parameter Symbol Min Max Unit
Supply Voltage Vcc -0.5 4.5 V
Storage Temperature Ts -40 +85 °C
Operating Humidity – 5 85 %

推荐工作条件 / Recommended Operating Conditions

Parameter Symbol Min Typical Max Unit
Operating Case Temperature Tc 0 +70 °C
Power Supply Voltage Vcc 3.135 3.30 3.465 V
Power Supply Current Icc 400 mA
Data Rate 25.78 Gbps

光学与电特性 / Optical and Electrical Characteristics

Parameter Symbol Min Typical Max Unit Notes
Transmitter
Centre Wavelength λc λc-6.5 λc λc+6.5 nm
Spectral Width(-20dB) Δλ 1 nm
Side-Mode Suppression Ratio SMSR 30 – dB
Average Output Power Pout 0 6 dBm Level1 1
1 6 Level2
4 7 Level3
Extinction Ratio ER 3.5 dB
Data Input Swing Differential VIN 180 850 mV 2
Input Differential Impedance ZIN 90 100 110 Ω
TX Disable Disable 2.0 Vcc V
Enable 0 0.8 V
TX Fault Fault 2.0 Vcc V
Normal 0 0.8 V
Receiver
Centre Wavelength λc 1260 1620 nm
Receiver Sensitivity -11 dBm Level1 3
-13 Level2
-23 Level3
Receiver Overload 2 dBm Level1,2 3
-6 Level3
LOS De-Assert LOSD -14 dBm Level1,2
-20 Level3
LOS Assert LOSA -30 dBm Level1,2
-35 Level3
LOS Hysteresis 0.5 dB
Data Output Swing Differential Vout 300 900 mV 4
LOS High 2.0 Vcc V
Low 0.8 V

Notes:

1. The optical power is launched into SMF.

2. PECL input, internally AC-coupled and terminated.

3. Measured with a PRBS 231-1 test pattern @25.78Gps, BER ≤5×10-5.

4. Internally AC-coupled.

时序与电特性 / Timing and Electrical

Parameter Symbol Min Typical Max Unit
Tx Disable Negate Time t_on 2 ms
Tx Disable Assert Time t_off 100 µs
Time To Initialize, including Reset of Tx Fault t_init 300 ms
Tx Fault Assert Time t_fault 100 µs
Tx Disable To Reset t_reset 10 µs
LOS Assert Time t_loss_on 100 µs
LOS De-assert Time t_loss_off 100 µs
Serial ID Clock Rate f_serial_clock 100 400 KHz
MOD_DEF (0:2)-High VH 2 Vcc V
MOD_DEF (0:2)-Low VL 0.8 V

数字诊断 / Diagnostics

Parameter Range Unit Accuracy Calibration
Temperature 0 to +70 °C ±3°C Internal
Voltage 3.0 to 3.6 V ±3% Internal
Bias Current 0 to 100 mA ±10% Internal
TX Power dBm ±3dB Internal
RX Power dBm ±3dB Internal

数字诊断存储映射 / Digital Diagnostic Memory Map

The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA).

The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring.

The digital diagnostic memory map specific data field defines as following.

数字诊断存储映射 / Digital Diagnostic Memory Map

引脚定义 / Pin Descriptions

引脚定义 / Pin Descriptions

Pin Signal Name Description Plug Seq. Notes
1 VEET Transmitter Ground 1
2 TX FAULT Transmitter Fault Indication 3 Note 1
3 TX DISABLE Transmitter Disable 3 Note 2
4 SDA SDA Serial Data Signal 3
5 SCL SCL Serial Clock Signal 3
6 MOD_ABS Module Absent. Grounded within the module 3
7 RS0 Not Connected 3
8 LOS Loss of Signal 3 Note 3
9 RS1 Not Connected 3
10 VEER Receiver ground 1
11 VEER Receiver ground 1
12 RD- Inv. Received Data Out 3 Note 4
13 RD+ Received Data Out 3 Note 4
14 VEER Receiver ground 1
15 VCCR Receiver Power Supply 2
16 VCCT Transmitter Power Supply 2
17 VEET Transmitter Ground 1
18 TD+ Transmit Data In 3 Note 5
19 TD- Inv. Transmit Data In 3 Note 5
20 VEET Transmitter Ground 1

Notes:

Plug Seq.: Pin engagement sequence during hot plugging.

1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.

2) Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.

3) LOS is open collector output. Should be pulled up with 4.7k~10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

4) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES.

5) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.

推荐接口电路 / Recommended Interface Circuit

推荐接口电路 / Recommended Interface Circuit

机械尺寸 / Mechanical Dimensions

机械尺寸 / Mechanical Dimensions

订购信息 / Ordering Information

Part Number Product Description
FTCS-Cxx25G-10D-1 1271~1371nm, 25.78Gbps, LC, 10km , 0°C~+70°C, with DDM, Level 1
FTCS-Cxx25G-10D-2 1271~1371nm, 25.78Gbps, LC, 10km , 0°C~+70°C, with DDM, Level 2
FTCS-Cxx25G-10D-3 1271~1371nm, 25.78Gbps, LC, 10km , 0°C~+70°C, with DDM, Level 3
λC Wavelength Guide
Code λC Unit Code λC Unit Code λC Unit Code λC Unit
27 1271 nm 29 1291 nm 31 1311 nm 33 1331 nm
35 1351 nm 37 1371 nm

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.

公司名:北亿纤通 | F-tone Networks
地区:中国四川天府新区
服务区域:全球
联系方式:
企业电话:028-85255257 | 企业传真:028-85977702 | 企业手机:19081343401
Site:https://www.f-tone.com
人事部:hr@f-tone.com | 市场部:sales@f-tone.com | 技术支持:support@f-tone.com

本产品为光模块产品线,详细信息,请联系我们的销售人员,谢谢!

Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.