FTCS-1303-40Dxx 155Mbps 单模 SFP 光模块 1310nm 40km LC

FTCS-1303-40Dxx 为 155Mbps 单模 Single Mode SFP 光收发模块,采用 1310nm FP 激光器与 PIN 光电探测器,SMF 传输距离最远 40km,双工 LC 接口,单 +3.3V 供电,支持 SFP MSA 与 SFF-8472 实时数字诊断(DDM),提供商业级 0~+70℃ 与工业级 -40~+85℃ 两种温度规格,适用于 155M 光传输、快速以太网与 SONET OC-3 等场景。

产品特点 / Product Features

  • 支持最高 155Mbps 速率
  • 热插拔 SFP 封装
  • 1310nm FP 激光器与 PIN 光电探测器,SMF 传输最远 40km
  • 符合 SFP MSA 与 SFF-8472,双工 LC 接口
  • 符合 RoHS
  • 单 +3.3V 供电
  • 实时数字诊断监控(DDM)
  • 工作温度:商业级 0~+70℃,工业级 -40~+85℃

应用场景 / Applications

  • 155Mbps 光传输系统
  • 快速以太网
  • SONET OC-3 LR2
  • 其他光链路

产品描述 / Description

该 SFP 光模块为高性能、低成本的 155Mbps 单模 Single Mode光收发一体模块,支持 125Mbps / 155Mbps 数据速率与 40km 传输距离。

模块由三部分组成:FP 激光发射单元、集成跨阻放大器(TIA)的 PIN 光电探测接收单元,以及 MCU 控制单元。全部模块满足 Class 1 激光安全要求。

模块兼容 SFP 多源协议(MSA)与 SFF-8472 数字诊断功能。

极限条件 / Absolute Maximum Ratings

参数 Parameter 符号 Symbol 最小值 Min 最大值 Max 单位 Unit
Supply Voltage Vcc -0.5 4.5 V
Storage Temperature Ts -40 +85 °C
Operating Humidity – 5 85 %

推荐工作条件 / Recommended Operating Conditions

参数 Parameter 符号 Symbol 最小值 Min 典型值 Typ 最大值 Max 单位 Unit
Operating Case Temperature Standard Tc 0 +70 °C
Operating Case Temperature Extended -20 +80 °C
Operating Case Temperature Industrial -40 +85 °C
Power Supply Voltage Vcc 3.135 3.30 3.465 V
Power Supply Current Icc 300 mA
Data Rate 155 Mbps

光学与电学特性 / Optical and Electrical Characteristics

发射端 / Transmitter

参数 Parameter 符号 Symbol 最小值 Min 典型值 Typ 最大值 Max 单位 Unit 备注 Notes
Centre Wavelength λc 1260 1310 1360 nm
Spectral Width(RMS) Δλ 3 nm
Side-Mode Suppression Ratio SMSR – – – dB
Average Output Power Pout -8 -3 dBm 1
Extinction Ratio ER 9.0 dB
Data Input Swing Differential VIN 180 1200 mV 2
Input Differential Impedance ZIN 90 100 110 Ω
TX Disable Disable 2.0 Vcc V
TX Disable Enable 0 0.8 V
TX Fault Fault 2.0 Vcc V
TX Fault Normal 0 0.8 V

接收端 / Receiver

参数 Parameter 符号 Symbol 最小值 Min 典型值 Typ 最大值 Max 单位 Unit 备注 Notes
Centre Wavelength λc 1260 1610 nm
Receiver Sensitivity -32 dBm 3
Receiver Overload -8 dBm 3
LOS De-Assert LOSD -33 dBm
LOS Assert LOSA -45 dBm
LOS Hysteresis 0.5 4 dB
Data Output Swing Differential Vout 600 800 1000 mV 4
LOS High 2.0 Vcc V
LOS Low 0.8 V

1. 光功率为注入 SMF 的实测值。

2. PECL 输入,内部 AC 耦合与端接。

3. 测试条件为 PRBS 223-1,155Mbps,BER ≤1×10-12。

4. 内部 AC 耦合。

时序与电学参数 / Timing and Electrical

参数 Parameter 符号 Symbol 最小值 Min 典型值 Typ 最大值 Max 单位 Unit
Tx Disable Negate Time t_on 1 ms
Tx Disable Assert Time t_off 10 µs
Time To Initialize, including Reset of Tx Fault t_init 300 ms
Tx Fault Assert Time t_fault 100 µs
Tx Disable To Reset t_reset 10 µs
LOS Assert Time t_loss_on 100 µs
LOS De-assert Time t_loss_off 100 µs
Serial ID Clock Rate f_serial_clock 100 400 KHz
MOD_DEF (0:2)-High VH 2 Vcc V
MOD_DEF (0:2)-Low VL 0.8 V

数字诊断 / Diagnostics

参数 Parameter 范围 Range 单位 Unit 精度 Accuracy 校准 Calibration
Temperature 0 to +70 °C ±3°C Internal
Temperature -20 to +80
Temperature -40 to +85
Voltage 3.0 to 3.6 V ±3% Internal
Bias Current 0 to 100 mA ±10% Internal
TX Power -8 to -3 dBm ±3dB Internal
RX Power -32 to -6 dBm ±3dB Internal

数字诊断存储映射 / Digital Diagnostic Memory Map

模块提供串行 ID 存储内容与当前工作状态的诊断信息,符合 SFF-8472 规范。

诊断信息可采用内部校准或外部校准方式实现,具体数据字段定义如下图所示。

数字诊断存储映射图(A0h/A2h 各 256 字节 EEPROM 分区定义)

图 1 数字诊断存储映射(A0h / A2h)

引脚定义 / Pin Descriptions

SFP 20 针金手指引脚定义示意图(Towards Bezel / Towards ASIC)

图 2 SFP 引脚定义示意图

引脚 Pin 信号名称 Signal 功能描述 Description 插合顺序 Plug Seq. 备注 Notes
1 VEET Transmitter Ground 1
2 TX FAULT Transmitter Fault Indication 3 Note 1
3 TX DISABLE Transmitter Disable 3 Note 2
4 SDA SDA Serial Data Signal 3
5 SCL SCL Serial Clock Signal 3
6 MOD_ABS Module Absent. Grounded within the module 3
7 RS0 Not Connected 3
8 LOS Loss of Signal 3 Note 3
9 VEER Receiver ground 1
10 VEER Receiver ground 1
11 VEER Receiver ground 1
12 RD- Inv. Received Data Out 3 Note 4
13 RD+ Received Data Out 3 Note 4
14 VEER Receiver ground 1
15 VCCR Receiver Power Supply 2
16 VCCT Transmitter Power Supply 2
17 VEET Transmitter Ground 1
18 TD+ Transmit Data In 3 Note 5
19 TD- Inv. Transmit Data In 3 Note 5
20 VEET Transmitter Ground 1

插合顺序(Plug Seq.):热插拔过程中引脚的接通次序。

1) TX Fault 为开集输出,主机板需以 4.7k~10kΩ 上拉至 2.0~Vcc 之间电压。

2) TDIS >2.0V 或悬空时激光输出关断,TDIS <0.8V 时开启。

3) LOS 为开集输出,主机板需以 4.7k~10kΩ 上拉至 2.0~Vcc 之间电压。

4) RD-/+:接收差分输出,内部 AC 耦合、100Ω 差分端接。

5) TD-/+:发射差分输入,内部 AC 耦合、100Ω 差分端接。

推荐接口电路 / Recommended Interface Circuit

推荐接口电路(Host Board 与 SFP 模块信号互连)

图 3 推荐接口电路

机械尺寸 / Mechanical Dimensions

机械尺寸图(单位:mm)

图 4 机械尺寸(单位:mm)

订购信息 / Ordering Information

型号 Part Number 产品描述 Product Description
FTCS-1303-40D 1310nm, 155Mbps, LC, 40km, 0°C~+70°C, with DDM
FTCS-1303-40DI 1310nm, 155Mbps, LC, 40km, -40°C~+85°C, with DDM
公司名:北亿纤通 | F-tone Networks
地区:中国四川天府新区
服务区域:全球
联系方式:
企业电话:028-85255257 | 企业传真:028-85977702 | 企业手机:19081343401
Site:https://www.f-tone.com
人事部:hr@f-tone.com | 市场部:sales@f-tone.com | 技术支持:support@f-tone.com

本产品为155M SFP光模块产品线,详细信息,请联系我们的销售人员,谢谢!

Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.