产品概述 / Description
FTCP-851X-02D 是一款 10.3Gbps SFP+ 多模光收发器,内置发送端与接收端 CDR(时钟数据恢复),采用 850nm VCSEL 激光器与 PIN 光电探测器,在 OM3 多模光纤(MMF)上支持最长 300m 的传输距离。模块支持 11.3Gbps 速率,符合 SFP+ MSA 与 SFF-8472 规范,配双工 LC 光接口,功耗低于 1W,支持实时数字诊断监控(DDM),单 +3.3V 供电,标准型工作温度 0°C~+70°C。
The SFP+ transceivers are high performance (with TX&RX CDR), cost effective modules supporting data rate of 10.3Gbps.
The transceiver consists of three sections: a VCSEL laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.
The transceivers are compatible with SFP Multi-Source Agreement and SFF-8472 digital diagnostics functions.

产品特点 / Product Features
- Supports up to 11.3Gbps bit rates
- Built-in TX and RX CDR
- Hot-pluggable SFP+ footprint
- 850nm VCSEL laser and PIN photodiode, Up to 300m for OM3-MMF transmission
- Compliant with SFP+ MSA and SFF-8472 with duplex LC receptacle
- Compatible with RoHS
- Single +3.3V power supply
- Power dissipation <1W
- Real Time Digital Diagnostic Monitoring
- Operating case temperature: Standard: 0 to +70°C
应用场景 / Applications
- 10GBASE-SR at 10.3125Gbps
- 10GBASE-SW at 9.953Gbps
- Other Optical links
技术参数 / Specifications
绝对最大额定值 / Absolute Maximum Ratings
| Parameter | Symbol | Min | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | Vcc | -0.5 | 4.5 | V |
| Storage Temperature | Ts | -40 | +85 | °C |
| Operating Humidity | – | 5 | 85 | % |
推荐工作条件 / Recommended Operating Conditions
| Parameter | Symbol | Min | Typical | Max | Unit |
|---|---|---|---|---|---|
| Operating Case Temperature (Standard) | Tc | 0 | +70 | °C | |
| Operating Case Temperature (Extended) | -20 | +80 | °C | ||
| Operating Case Temperature (Industrial) | -40 | +85 | °C | ||
| Power Supply Voltage | Vcc | 3.135 | 3.30 | 3.465 | V |
| Power Supply Current | Icc | 500 | mA | ||
| Data Rate | 9.953 | 10.3125 | 11.3 | Gbps |
光学与电气特性 / Optical and Electrical Characteristics
| Parameter | Symbol | Min | Typical | Max | Unit | Notes |
|---|---|---|---|---|---|---|
| Transmitter | ||||||
| Centre Wavelength | λc | 840 | 850 | 860 | nm | |
| Spectral Width(RMS) | Δλ | 0.45 | nm | |||
| Side-Mode Suppression Ratio | SMSR | – | – | – | dB | |
| Average Output Power | Pout | -6.0 | -0.5 | dBm | 1 | |
| Extinction Ratio | ER | 3.0 | dB | |||
| Output Eye Diagram margin | 15 | % | 5 | |||
| Data Input Swing Differential | VIN | 180 | 950 | mV | 2 | |
| Input Differential Impedance | ZIN | 90 | 100 | 110 | Ω | |
| TX Disable | Disable | 2.0 | Vcc | V | ||
| TX Disable | Enable | 0 | 0.8 | V | ||
| TX Fault | Fault | 2.0 | Vcc | V | ||
| TX Fault | Normal | 0 | 0.8 | V | ||
| Receiver | ||||||
| Centre Wavelength | λc | 840 | 850 | 860 | nm | |
| Receiver Sensitivity | -10.5 | dBm | 3 | |||
| Receiver Overload | 0.5 | dBm | 3 | |||
| LOS De-Assert | LOSD | -12 | dBm | |||
| LOS Assert | LOSA | -22 | dBm | |||
| LOS Hysteresis | 0.5 | 4 | dB | |||
| Data Output Swing Differential | Vout | 500 | 700 | 900 | mV | 4 |
| LOS | High | 2.0 | Vcc | V | ||
| LOS | Low | 0.8 | V | |||
Notes:
1. The optical power is launched into MMF.
2. PECL input, internally AC-coupled and terminated.
3. Measured with a PRBS 231-1 test pattern @10312Mbps, BER ≤1×10-12.
4. Internally AC-coupled.
5. Compliant with ITUT and IEEE recommendation MASK.
光纤传输距离 / Fiber Operating Range
| Fiber type | Minimum modal bandwidth @ 850 nm (MHz·km) | Operating range (meters) |
|---|---|---|
| 62.5 µm MMF | 160 | 2 to 26 |
| 62.5 µm MMF | 200 | 2 to 33 |
| 50 µm MMF | 400 | 2 to 66 |
| 50 µm MMF | 500 | 2 to 82 |
| 50 µm MMF | 2000 | 2 to 300 |
时序与电气 / Timing and Electrical
| Parameter | Symbol | Min | Typical | Max | Unit |
|---|---|---|---|---|---|
| Tx Disable Negate Time | t_on | 1 | ms | ||
| Tx Disable Assert Time | t_off | 10 | µs | ||
| Time To Initialize, including Reset of Tx Fault | t_init | 300 | ms | ||
| Tx Fault Assert Time | t_fault | 100 | µs | ||
| Tx Disable To Reset | t_reset | 10 | µs | ||
| LOS Assert Time | t_loss_on | 100 | µs | ||
| LOS De-assert Time | t_loss_off | 100 | µs | ||
| Serial ID Clock Rate | f_serial_clock | 100 | 400 | KHz | |
| MOD_DEF (0:2)-High | VH | 2 | Vcc | V | |
| MOD_DEF (0:2)-Low | VL | 0.8 | V |
数字诊断 / Diagnostics
| Parameter | Range | Unit | Accuracy | Calibration |
|---|---|---|---|---|
| Temperature | 0 to +70 | °C | ±3°C | Internal |
| Voltage | 3.0 to 3.6 | V | ±3% | Internal |
| Bias Current | 0 to 15 | mA | ±10% | Internal |
| TX Power | -6.0 to -0.5 | dBm | ±3dB | Internal |
| RX Power | -10.5 to -1 | dBm | ±3dB | Internal |
数字诊断存储映射 / Digital Diagnostic Memory Map
The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA).
The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring. The digital diagnostic memory map specific data field defines as following.

引脚定义 / Pin Descriptions

| Pin | Signal Name | Description | Plug Seq. | Notes |
|---|---|---|---|---|
| 1 | VEET | Transmitter Ground | 1 | |
| 2 | TX FAULT | Transmitter Fault Indication | 3 | Note 1 |
| 3 | TX DISABLE | Transmitter Disable | 3 | Note 2 |
| 4 | SDA | SDA Serial Data Signal | 3 | |
| 5 | SCL | SCL Serial Clock Signal | 3 | |
| 6 | MOD_ABS | Module Absent. Grounded within the module | 3 | |
| 7 | RS0 | Not Connected | 3 | |
| 8 | LOS | Loss of Signal | 3 | Note 3 |
| 9 | RS1 | Not Connected | 3 | |
| 10 | VEER | Receiver ground | 1 | |
| 11 | VEER | Receiver ground | 1 | |
| 12 | RD- | Inv. Received Data Out | 3 | Note 4 |
| 13 | RD+ | Received Data Out | 3 | Note 4 |
| 14 | VEER | Receiver ground | 1 | |
| 15 | VCCR | Receiver Power Supply | 2 | |
| 16 | VCCT | Transmitter Power Supply | 2 | |
| 17 | VEET | Transmitter Ground | 1 | |
| 18 | TD+ | Transmit Data In | 3 | Note 5 |
| 19 | TD- | Inv. Transmit Data In | 3 | Note 5 |
| 20 | VEET | Transmitter Ground | 1 |
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2) Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3) LOS is open collector output. Should be pulled up with 4.7k~10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
4) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES.
5) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.
推荐接口电路 / Recommended Interface Circuit

机械尺寸 / Mechanical Dimensions

订购信息 / Ordering Information
| Part Number | Product Description |
|---|---|
| FTCP-851X-02D | 850nm, 10.3Gbps with Tx and Rx CDR, LC, 300m, 0°C~+70°C, with DDM |
地区:中国四川天府新区
服务区域:全球
联系方式:
企业电话:028-85255257 | 企业传真:028-85977702 | 企业手机:19081343401
Site:https://www.f-tone.com
人事部:hr@f-tone.com | 市场部:sales@f-tone.com | 技术支持:support@f-tone.com
本产品为光模块产品线,详细信息,请联系我们的销售人员,谢谢!
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.



















