BYCS-Bxx1X-10Dxxxx 10G SFP+ BIDI光模块 10km(1270/1330nm)

产品特点 / Product Features

10Gb/s serial optical interface compliant to 802.3ae 10GBASE-LR

Electrical interface compliant to SFF-8431 specifications for enhanced 8.5 and 10 Gigabit small form factor pluggable module “SFP+”

1270/1330nm DFB transmitter, PIN photo-detector

2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers

ll-metal housing for superior EMI performance

Low power consumption

Advanced firmware allow customer system encryption information to be stored in transceiver

Cost effective SFP+ solution, enables higher port densities and greater bandwidth

RoHS compliant​

Operating case temperature range:

Commercial:0 to 70℃

Industrial: -40 to 85℃

应用场景 / Applications

High-speed storage area networks

Computer cluster cross-connect

Custom high-speed data pipes

产品概述 / Description

This 1270/1330nm DFB 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 10km.

The SFP+ module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mm of standard FR4 with one connector.

The transmitter converts 10Gbit/s serial CML electrical data into serial optical data compliant with the 10GBASE-LR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ. TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kΩ to 10 kΩ resistor

The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.

推荐应用电路 / Proposed Application Schematics

推荐应用电路(一)

推荐应用电路(二)

功能框图 / Functional Block Diagram

模块由发射、接收与控制三部分组成:发射侧由 MCU 通过 LD Bias / MOD-DEF 控制激光器驱动器(LD Driver),驱动激光器输出光信号;接收侧由光电探测器(内置跨阻放大器 TIA)与后级限幅放大器(Post Amp)恢复电信号;MCU 经 I2C(SDA/SCL)对外提供温度、电压、偏置电流、收发光功率等数字诊断信息,并处理 TX Disable、TX Fault、LOS 等控制与告警信号。

收发功能框图

技术参数 / Specifications

绝对最大额定值 / Absolute Maximum Ratings

Parameter Symbol Min Max Units
Power Supply Voltage Vcc 0 3.6 V
Storage Temperature Tc -40 85 C
Operating Case Temperature Tc 0 70 C
-40 85
Relative Humidity RH 5 95 %
RX Input Average Power Pmax 0 dBm

Note:

Exceeding any of these values may immediately damage the device.

推荐工作条件 / Recommended Operating Conditions

Parameter Symbol Min Typ Max Units
Power Supply Voltage Vcc 3.135 3.3 3.465 V
Power Supply Current Icc 350 mA
Operating Case Temperature TC 0 25 70 C
-40 25 85

Note:

Recommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless otherwise noted.

光学特性 / Optical Characteristics

Parameters Unit Values
Operating Reach m 10K
Transmitter
Center wavelength (range) nm 1270/1330
Side Mode Suppression Ratio (min) dB 30
Launched power
– maximum (Average) dBm 0.5
– minimum (Average) dBm -8.2
Extinction ratio (min) dBm -5.2
RIN12 OMA (max) dBm -6.2
Transmitter and dispersion penalty (max) dB 3.2
Average launch power of OFF transmitter (max) dBm -30
Extinction ratio (min) dB 3.5
RIN12 OMA (max) dB/Hz -128
Optical Return Loss Tolerance (min) dB 12
Receiver
Center wavelength (range) nm 1270/1330
Receive overload (max) in average power(note 1) dBm 0.5
Receive sensitivity (min) in average power(note 1) dBm -14.4
Receiver Reflectance (max) dB -12
Vertical eye closure penalty (min)(note 3) dB 2.2
Los Assert(min) dBm -30
Los Dessert(max) dBm -15
Los Hysteresis(min) dB 0.5
Stressed eye jitter (min)(note 2) UIp-p 0.3
Receive electrical 3dB upper cutoff frequency (max) GHz 12.3
Receiver power (damage, Max) dBm 3

Note:

Average optical power shall be measured using the methods specified in TIA/EIA-455-95.

Receiver sensitivity is informative. Stressed receiver sensitivity shall be measured with conformance test signal for BER =1x 10-12 .

Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver.

Power budget is defined as the different between the Rx sensitivity and the Tx output power of the interface.

Path penalty is intended as the power penalty of the interface between back-to-back and the maximum applied dispersion.

数字诊断功能 / Digital Diagnostic Functions

Parameter Symbol Min Max Unit Notes
Temperature monitor absolute error DMI_Temp -3 3 ℃ Over operating temp
Laser power monitor absolute error DMI_TX -3 3 dB
RX power monitor absolute error DMI_RX -3 3 dB -1dBm to -15dBm range
Supply voltage monitor absolute error DMI_VCC -0.08 0.08 V Full operating range
Bias current monitor DMI_Ibias -10% 10% mA

Note:

The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless otherwise specified. It is compliant to SFF8472 Rev10.2 with internal calibration mode. For external calibration mode please contact our sales stuff.

电特性 / Electrical Characteristics

Parameter Symbol Min Typ Max Unit Notes
Data Rate / 10.3125 Gbps
Power Consumption / 800 1000 mW
Transmitter
Single Ended Output
Voltage Tolerance
-0.3 4 V
C common mode voltage tolerance 15 mV
Tx Input Diff Voltage VI 180 800 mV
Tx Fault VoL -0.3 0.4 V At 0.7mA
Data Dependent Input Jitter DDJ 0.1 UI
Data Input Total Jitter TJ 0.28 UI
Receiver
Single Ended Output
Voltage Tolerance
-0.3 4 V
Rx Output Diff Voltage Vo 300 850 mV
Rx Output Rise and Fall Time Tr/Tf 30 ps 20% to 80%
Total Jitter TJ 0.7 UI
Deterministic Jitter DJ 0.42 UI

Note:

The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified.

控制与状态 I/O 时序特性 / Control and Status I/O Timing Characteristics

Parameter Symbol Min Max Unit Condition
TX Disable Assert Time t_off 10 μs Time from rising edge of TX Disable to when the optical output falls below 10% of nominal
TX Disable Negate Time t_on 1 ms Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal
Time to initialize,including reset of TX_Fault t_init 300 ms From power on or negation of TX Fault using TX Disable
TX Fault Assert Time t_fault 100 μs Time from fault to TX fault on
TX Disable to reset t_reset 10 μs Time TX Disable must be held high to reset TX fault
LOS Assert Time t_loss_on 100 μs Time from LoS state to RX LOS assert
LOS Deassert Time t_loss_off 100 μs Time from non-LOS state to RX LOS deassert
Rate-Select Change Time t_ratesel 10 μs Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification
Serial lD Clock Rate t_serial_clock 100 kHz

Note:

Timing characteristics of control and status I/O are included in Table 8, which is also defined in SFF-8431.

引脚定义 / Pin Assignment and Description

引脚定义(20-Pin)

引脚方向示意(Bottom of Board / Top View)

PIN Definition
PIN Logic Symbol Description Notes
1 VeeT Module Transmitter Ground 1
2 LVTTL-O TX_Fault Module Transmitter Fault
3 LVTTL-I TX_Dis Transmitter Disable; Turns off transmitter laser output
4 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2
5 LVTTL-I SCL 2-Wire Serial Interface Clock 2
6 MOD_DEF0 Module Definition, Grounded in the module
7 LVTTL-I RS0 Receiver Rate Select
8 LVTTL-O RX_LOS Receiver Loss of Signal Indication Active LOW
9 LVTTL-I RS1 Transmitter Rate Select (not used)
10 VeeR Module Receiver Ground 1
11 VeeR Module Receiver Ground 1
12 CML-O RD- Receiver Inverted Data Output
13 CML-O RD+ Receiver Data Output
14 VeeR Module Receiver Ground 1
15 VccR Module Receiver 3.3 V Supply
16 VccT Module Receiver 3.3 V Supply
17 VeeT Module Transmitter Ground 1
18 CML-I TD+ Transmitter Non-Inverted Data Input
19 CML-I TD- Transmitter Inverted Data Input
20 VeeT Module Transmitter Ground 1

Note:

Module ground pins GND are isolated from the module case.

Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.

机械规格 / Mechanical Specifications

LC Interface

SC Interface

LC 接口机械尺寸

SC 接口机械尺寸

ESD 静电防护 / ESD

This transceiver is specified as ESD threshold 2kV for all electrical input pins, tested per MIL-STD-883, Method 3015.4 /JESD22-A114-A (HBM). However, normal ESD precautions are still required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD protected environment.

激光安全 / Laser Safety

This is a Class 1 Laser Product according to IEC 60825-1:1993:+A1:1997+A2:2001. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated (July 26, 2001).

订购信息 / Ordering Information

Model Specification Description
BYCS-B271X-10D SFP+ BIDI, SM, 10.3125G, T1270-R1330nm, 10km, with DDM, LC, 0 ~ 70℃
BYCS-B331X-10D SFP+ BIDI, SM, 10.3125G, T1330-R1270nm, 10km, with DDM, LC, 0 ~ 70℃
BYCS-B271X-10DI SFP+ BIDI, SM, 10.3125G, T1270-R1330nm, 10km, with DDM, LC, -40 ~ 85℃
BYCS-B331X-10DI SFP+ BIDI, SM, 10.3125G, T1330-R1270nm, 10km, with DDM, LC, -40 ~ 85℃
BYCS-B271X-10DS SFP+ BIDI, SM, 10.3125G, T1270-R1330nm, 10km, with DDM, SC, 0 ~ 70℃
BYCS-B331X-10DS SFP+ BIDI, SM, 10.3125G, T1330-R1270nm, 10km, with DDM, SC, 0 ~ 70℃
BYCS-B271X-10DSI SFP+ BIDI, SM, 10.3125G, T1270-R1330nm, 10km, with DDM, SC, -40 ~ 85℃
BYCS-B331X-10DSI SFP+ BIDI, SM, 10.3125G, T1330-R1270nm, 10km, with DDM, SC, -40 ~ 85℃
公司名:北亿纤通 | F-tone Networks
地区:中国四川天府新区
服务区域:全球
联系方式:
企业电话:028-85255257 | 企业传真:028-85977702 | 企业手机:19081343401
Site:https://www.f-tone.com
人事部:hr@f-tone.com | 市场部:sales@f-tone.com | 技术支持:support@f-tone.com

本产品为光模块产品线,详细信息,请联系我们的销售人员,谢谢!

Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.